If you are like me, you may be thinking that building your own convention built fishing rod would be a difficult endeavour. When I first discovered that it was possible to convention build a fishing rod, I put off the decision to do it. I notion I probably didn't have enough skill. Probably extra tools were needed. I thought it might be a involved task that would take up too much space in my home.
When I finally decided to get more information, I was about 18 years old (30 years ago!) and was surprised to discover just how easy building my own fishing rod could be! Not only that, work space requirements are not much at all. All you indubitably need is space that is a bit wider than the section lengths of the rod blank you select to build your rod on. For example, if you are building a 7 foot rod that comes in two pieces, all you'll need is a bit more space than 3 1/2 feet wide.
Tool Sets Hand Tools
Custom building fishing rods can get involved depending if you want to even make your own reel seats and cork handles, but for most of us, purchasing the components is what we'll do. Generally, for fly and spinning rods, you'll need to purchase:
Best Price Allied 49035 41-Piece SAE Tap and Die Tool Set
Allied 49035 41-Piece SAE Tap and Die Tool Set Feature
- 41-piece tap and die tool set
- Threads and bore taps quickly and easily with professional results
- Precision machined steel taps, dies, and accessories
- Selection of national coarse and fine thread sizes
- Includes adjustable tap wrench, die handle and pitch gauge
Allied 49035 41-Piece SAE Tap and Die Tool Set Overview
When faced with them, stripped spark plug holes and mangled bolts and nuts are a pain, for sure. You can hunt down the right tap and die for the job in each instance, but it’s a lot easier and affordable to have a whole kit on hand and at the ready. A must-have tool set for pros and serious do-it-yourselfers alike, this 41-piece set lets you cut threads and bore taps quickly and easily with professional results. Precision machined steel construction ensures years of clean threads and taps. A selection of national coarse and fine thread sizes means steadfast attachments for years to come. --Brian D. OlsonWhat’s in the Box
Adjustable tap wrench, die handle & pitch gauge
Available at Amazon Check Price Now!
Related Products
- Neiko Professional-Grade 40-Piece High-Strength Steel Alloy Tap & Die Hexagon Set - Metric - M3 to M12
- Mibro 301370 26-Piece Tap Die and Drill Metric Set
- 6 Inch LCD Digital Caliper with Extra Battery and Case
- Black Oxide Alloy Steel Set Screw, Hex Socket Drive, Cup Point, #4-40, 1/8" Length (Pack of 100)
- Neiko 3-Piece Titanium Step Drill Bits Set M2 Steel - 28 Sizes, SAE
Customer Reviews
*** Product Information and Prices Stored: Aug 17, 2012 15:45:05
The fishing rod blank. Cork cope (spinning rods wish a "butt grip" and a "fore grip." Reel seat. Guides and tip top. Nylon rod wrapping thread. Epoxy. Rod wrapping discontinue epoxy. Winding check that is put on the rod at the tip end of the fore grip. Hook Keeper if desired on your rod. Butt cap
The basic steps to building your own spin fishing rod are:
Determine where the spine of the fishing rod blank is, and mark it on the blank. This will be used to rule on which axis of the blank the guides will be secured. improve the pre-drilled hole in the cork grip(s) to fit the butt of the blank, if required. Fit the butt grip onto the blank after applying epoxy to the blank where the butt grip will be. Fit the reel seat to the blank by building up the area in the middle of the blank and inside of the reel seat, using strips of masking tape and then apply epoxy to gather the reel seat in place. Align the reel seat correctly with the axis of the rod that the guides will be on. Fit the fore grip to the blank after applying epoxy. Set the rod aside to allow the epoxy to cure for 24 hours. rule the spacing of the guides - a beginner may want to refer to a normal guide spacing chart and make minor adjustments depending on the rod blank being used. Using a file, grind down the feet of the guides so they taper thinly where the thread will be wrapped over. Attach the guides to the rod blank using a strip of masking tape. The use of the masking tape is temporary. Using the thread, wrap and gather the guide feet, removing the masking tape as the approaches the tape. gather the tip top with hot melt glue. Make a ornamental wrap above the fore grip if desired and attach the hook keeper in the same way the guides were attached. Apply rod wrapping discontinue to the threads. If you have a slow Rpm (7 to 20 Rpm) motor that you can attach the rod to, that's exquisite for ensuring there is no sagging of the discontinue while it is curing. If not, you can turn the rod by hand for the first half hour and then 25 degree turns every 10 or fifteen minutes for a few hours after. When the thread wrap discontinue has cured, attach the Butt cap to the butt end of the rod.
Some of the above steps such as wrapping the guides with thread may take a bit of practice, but is not difficult to do. Once you've built your first rod, you'll want to learn more about all the distinct components that are ready to you, finishes, and probably increase your skills in production ornamental thread wraps.
One thing for sure - you'll be very proud when you catch your first fish on the rod you've built yourself!
How Hard is it to Build a Fishing Rod?Friends Link : Band Saws Woodworking Tools home improvement Sander Accessories Cordless Staplers
No comments:
Post a Comment